Imagine you press the remote button of the garage door opener, but it’s not working. We know It is a headache on winter or rainy days when the manual opening is challenging. That’s why knowing How to program a genie garage door opener is important.
First, understand that a genie garage door opener includes three programming devices. The following is a genie remote control, keypad, and wall console. However, the manufacturer offers easy-to-follow instructions to program the type of genie garage door openers.
Depending on your device, you have to program their settings. This is a detailed discussion to program different genie garage door openers, So check out below.
3 Methods to Program a Genie Garage Door Opener?
As mentioned, three types of genie garage door openers are available for different door types. They are as follows:
- By Remote Control
- By Keypad
- By Wall Console
Programming these devices is not complicated, but you must follow a specific process. Indeed, each device has a specific instruction program.
How to Program a Genie Remote Control?
The manufacturer offers three different types of remotes for various garage door openers. First, you have to ensure which type of remote you own. Check out the owner’s manual to understand the model type. After that, follow the steps to program different genie remote controls.
Intellicode I Remotes
- Press and hold the Receiver learn code button to start the programming process.
- Release the button when you notice blinking light.
- Now press the remote button three times to connect the remote to the opener.
- You can operate the door on the fourth press and successfully program the remote.
Note: – Receiver learns the code button near the opener’s motor head. Besides, press the remote button within two feet of the opener.
Intellicode II Remotes
- Press the Receiver learn code button located underneath the motor head.
- Hold and release the button when you notice a blue LED.
- Wait a second; the blue LED will turn purple.
- Now press the remote button five times within 5 feet of the opener motor head.
- The door will start moving on the fifth press, which means the programming is successful.
Note: – if you want to clear an existing or stolen remote setting, press and hold the square (Receiver) button until a blue LED appears. Wait for the second blue LED to turn purple; keep pressing the triangle button until the purple color turns off.
Intellicode III Remotes
- Locate the motor head for the square button underneath the genie door opener.
- Press and hold the switch until the blue color appears.
- Release and press again to turn blue in blinking purple.
- Now press the remote button to solidify the purple LED and start programming the door opener.
How to Program a Genie Keypad?
Programming a genie keypad is relatively easier than creating a remote control. By entering the default pin and program button, settings can be adjustable. So below are the steps to program a genie keypad.
- Before starting the programming, make sure the backlight is off.
- Now press the “learn” or “program” button on the motor unit’s backside.
- Hold the button until the LED turns blue, which means the device is in programing mode.
- Release the switch and wait for the motor LED to start blinking purple.
- Now enter the default using the keypad button, 357.
- Slowly press the up/down button to ensure the garage door is opening.
You can also change the default pin by following simple steps.
- Enter the default pin and press the program button.
- Enter your new pin from three to eight digits.
- Again press the program button to confirm the code.
How to Program a Genie Wall Console?
Lastly comes another genie garage door opener called wall console. This is a small wall-installed device on your garage wall. Programming this wall console is also easier than most people think. So below are the steps to follow.
- First, locate the program button backside of the motor unit.
- Press and hold the switch until a blue LED turns on.
- Release the button when it turns purple or blinking.
- Go to the wall console and press the door button.
- Hold it until the ring LED turns on or blinks, which means the device is in syncing mode.
- Press and release the open, close, and other buttons to ensure the garage door works.
Common Challenges While Programming a Genie Garage Door Opener
Reprogramming or replacing the remote, console, or keypad is sometimes unnecessary. In many cases, the problem may seem other than the genie remote. So first, manually open or close the garage door to ensure it works. Secondly, inspect the following challenges common with genie garage door openers.
- The most common problem while programming a Genie garage door opener remote is accessing the device from too much distance. As mentioned, a genie remote should be operated within 5 feet of the door.
- Sometimes the remote stops working due to dead batteries, so replace it and reprogram the door.
- Avoid getting too close to the door, leading to battery issues.
- Genie garage door opener has limited memory capacity. So if your device already loads too many codes or settings, erase all the information and program again.
- Ensure the door sensor is working and doesn’t have any obstacles.
- Confirm the door Athena is visible and hanging from the opener’s head.
How to Reset a Genie Garage Door Opener?
Resetting a genie garage door opener may vary on the device type. However, the process is almost the same in every model. So below are the steps to reset your Genie garage door opener.
- First, locate the square button, the “learn or “program button. The switch is mainly located near the athena or back panel of the motor.
- Press and hold the button for 3 seconds.
- Release the button when the purple round shape LED lights up. Now the unit is in resetting mode.
- Press the remote button and wait until the opener’s LED turns solid.
- Now you can press any button to open or close your garage door.
FAQs While Programming Genie Garage Door Opener
How Do I Change the Code on My Genie Door Opener?
The Genie keypad comes with a default pin to program the garage door. You can change the code by entering the default pin and then the program button. A new display will open to confirm your new pin. Set your code and press the program button to change the default code.
How do I reprogram my Genie garage door wall control?
First, press the program button until the LED blinks. Now go to the wall console and press the door button. Wait a second, and the device will reprogram.
Conclusion
Genie offers different door opener devices, including a remote, wall console, and keypad. Each type has a different programming setting. So follow our recommended steps to reset or reprogram the openers. Remember, genie garage door openers have limited memory capacities. So timely change their setting to keep your garage door functional.
You May Also Like: